Refine Search
Filter Options Stacked Scrolling
Eval Board
Topology
Outputs and Type
Output Voltage: Factory Set
Current Out
Voltage In
Efficiency @ Conditions
Voltage Out Range
Features
Switching Frequency
Standby Current [Typical]
Quiescent Current [Typical]
Component Count + Extras
Internal Switch
Design Author
Application / Target Market
Main I.C. Base Part
More Filters

Designs (560)

560 Results - Page 1/56 |< < 1 2 3 4 5
Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output DC1693A: 5V @ 350mA Isolated, 4.5 ~ 30V in Manufacturer: Analog Devices Inc.

The demo circuit 1693A is an isolated flyback μModule® DC/DC converter featuring the LTM8047. The demo circuit is designed for a 5V output from a 4.5V to 30V input. The typical current capability of the 5V output varies with input voltage from about 110mA at VIN = 4.5V to about 350mA at VIN = 30V.

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output LM5118EVAL: 12V @ 3A, 5 ~ 75 Vin Manufacturer: Texas Instruments

The LM5118 evaluation board is designed to provide the design engineer with a fully functional, Emulated Current Mode Control, buck-boost power converter to evaluate the LM5118 controller IC. The evaluation board provides a 12V output with 3A of output current capability. The evaluation board’s wide input voltage range is from 75V to 5V, with operation down to 3V with some component changes. The e…

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output LM22670EVAL: 3.3V @ 3A, 4.5 ~ 42Vin Manufacturer: Texas Instruments

The LM22670 series of regulators are monolithic integrated circuits which provide all of the active functions for a step-down (buck) switching regulator capable of driving up to 3A loads with excellent line and load regulation characteristics. High efficiency (>90%) is obtained through the use of a low ON-resistance N-channel MOSFET.

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output LM5007EVAL: 10V @ 400mA, 12 ~ 75 Vin Manufacturer: Texas Instruments

The LM5007 Step down switching regulator features all of the functions needed to implement low cost, efficient, Buck bias regulators.

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output LM5574EVAL: 5V @ 500mA, 7 ~ 75 Vin Manufacturer: Texas Instruments

The LM5574 evaluation board is designed to provide the design engineer with a fully functional power converter based on Emulated Current Mode Control to evaluate the LM5574 regulator IC. The evaluation board provides a 5V output with a 0.5A current capability. The ultra-wide input voltage ranges from 7V to 75V. The design operates at 300kHz, a good compromise between conversion efficiency and so…

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output TPS54350EVM-235: 3.3V @ 3A, 6 ~ 18 Vin Manufacturer: Texas Instruments

The TPS54350 dc/dc converter is designed to provide up to 3-A output from a nominal 12-V (6-V to 18-V) input voltage source. Rated input voltage and output current range is given in Table 1−1. This evaluation module is designed to demonstrate the small PCB areas that may be achieved when designing with the TPS54350 regulator and does not reflect the high efficiencies that may be achieved when des…

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output LM5008EVAL: 10V @ 300mA, 12 ~ 95V in Manufacturer: Texas Instruments

The LM5008 Step down switching regulator features all of the functions needed to implement low cost, efficient, Buck bias regulators. This high voltage regulator contains a 100V, 0.5A N-channel Buck switch.

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output DC1198A-A: 12V @ 5A, 4.5 ~ 20V in Manufacturer:

Demonstration circuit DC1198A-A features the LTM®4605EV, the high efficiency, high density switch mode buck-boost μModule® regulator. The LTM4605EV can regulate its output voltage from an input voltage above, below, or equal to the output. The input voltage range of DC1198A-A is from 4.5V to 20V with a preset output voltage of 12V. The rated load current is 5A, although derating is necessary for …

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output DC1194A: 3.3V @ 200mA,4.5~36V in, Inductor On-Chip Manufacturer: Analog Devices Inc.

Demonstration circuit DC1194A features the LTM®8020, a 200mA DC/DC step-down μModule® regulator. The board is preset to deliver a 3.3V output at up to 200mA load current from an input voltage of up to 36V. The output voltage may be modified by simply changing one resistor.

Schematic View Design
AC/DC and DC/DC Conversion > DC/DC SMPS - Single Output DC1041A-B: 4.5V~28Vin, 12A Step Down Regulator Manufacturer: Analog Devices Inc.

Demonstration circuit DC1041A-A features the LTM®4601EV, a 12A high efficiency, high density switch mode step-down converter. The input voltage range is from 4.5V to 28V. The output voltage is jumper selectable for popular voltages from 0.6V to 5V. The PLLIN pin supports synchronizing the μModule® regulator to an external clock.

560 Results - Page 1/56 |< < 1 2 3 4 5
Terms & Conditions Privacy Notice Trade Compliance Accessibility Statement Cookie Settings Do Not Sell / Do Not Share My Personal Information
Local Support: 701 Brooks Avenue South, Thief River Falls, MN 56701 USA Copyright © 1995-2026, DigiKey. All Rights Reserved.
ECIA Member
ECIA Member